projects:automotive:kancil:k4_660_upgrades
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| projects:automotive:kancil:k4_660_upgrades [2026/03/11 14:49] – [⚡️ Contact Point → Electronic Distributor] Remove the emoji for cleaner permalink Andrew Yong | projects:automotive:kancil:k4_660_upgrades [2026/03/11 14:55] (current) – Rename heading and reword contact point coil switching Andrew Yong | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Perodua Kancil K4 660 Upgrades ====== | ====== Perodua Kancil K4 660 Upgrades ====== | ||
| - | ===== Contact Point → Electronic Distributor ===== | + | ===== From Contact Point Distributor to Electronic Distributor ===== |
| - | + | ==== Comparison ==== | |
| - | ==== ℹ️ | + | |
| ^ Parameter ^ Contact Point Distributor ^ Electronic Distributor (Transistor Controlled Ignition) ^ | ^ Parameter ^ Contact Point Distributor ^ Electronic Distributor (Transistor Controlled Ignition) ^ | ||
| ^ Shipped Models | Kancil 660 | Kancil 850 | | ^ Shipped Models | Kancil 660 | Kancil 850 | | ||
| - | ^ Coil Switching | Mechanical | Transistor | | + | ^ Coil Switching | Mechanical |
| ^ Coil Pulse | Slow | Sharp | | ^ Coil Pulse | Slow | Sharp | | ||
| ^ Timing | Changes over time due to contact point wear | Consistent | | ^ Timing | Changes over time due to contact point wear | Consistent | | ||
| Line 20: | Line 19: | ||
| However, it comes with the tradeoff that any failure of electronics will be sudden, without developing early warning symptoms, and a failed electronic distributor can generally only be repaired with a 1:1 swap. | However, it comes with the tradeoff that any failure of electronics will be sudden, without developing early warning symptoms, and a failed electronic distributor can generally only be repaired with a 1:1 swap. | ||
| - | ==== 🔧 Tools Required ==== | + | ==== Tools Required ==== |
| - 10mm hex socket wrench (optional, but good to have as nearly all other bolts are 10mm) | - 10mm hex socket wrench (optional, but good to have as nearly all other bolts are 10mm) | ||
| Line 26: | Line 25: | ||
| - 21mm spark plug socket wrench | - 21mm spark plug socket wrench | ||
| - | ==== 🛒 Parts Required ==== | + | ==== Parts Required ==== |
| ^ Qty ^ Unit ^ Item ^ Notes ^ | ^ Qty ^ Unit ^ Item ^ Notes ^ | ||
| Line 40: | Line 39: | ||
| ^ Qty ^ Unit ^ Item ^ Note ^ | ^ Qty ^ Unit ^ Item ^ Note ^ | ||
| - | | 1 | roll/pack | **[[https:// | + | | 1 | roll/pack | **[[https:// |
| - | | 1 | each | **[[https:// | + | | 1 | each | **[[https:// |
| - | + | ==== Wiring ==== | |
| - | ==== ⚡ Wiring ==== | + | |
| === Prepare the Power Cable === | === Prepare the Power Cable === | ||
| Line 75: | Line 73: | ||
| - Finish all heatshrinking/ | - Finish all heatshrinking/ | ||
| - | ==== 🔩 Remove the Old Distributor ==== | + | ==== Remove the Old Distributor ==== |
| - Mark the distributor angle: draw a line across engine block → distributor body with the paint marker | - Mark the distributor angle: draw a line across engine block → distributor body with the paint marker | ||
| Line 85: | Line 83: | ||
| * Minimise wiggling to preserve the shaft angle for reference when installing the new distributor | * Minimise wiggling to preserve the shaft angle for reference when installing the new distributor | ||
| - | ==== 🔩 Install the New Distributor ==== | + | ==== Install the New Distributor ==== |
| - Place old and new distributors side by side | - Place old and new distributors side by side | ||
| Line 96: | Line 94: | ||
| - Connect the power cable plug | - Connect the power cable plug | ||
| - | ==== ⚡️ | + | ==== Change Spark Plugs ==== |
| - Change all 3 spark plugs to the newly purchased resistive plugs so we have all our new ignition components installed before timing adjustment | - Change all 3 spark plugs to the newly purchased resistive plugs so we have all our new ignition components installed before timing adjustment | ||
| Line 103: | Line 101: | ||
| * Inspect the original spark plugs, if they are in good condition (no structural damage, excessive wear or heavy deposits), keep them as a spare together with the contact point distributor | * Inspect the original spark plugs, if they are in good condition (no structural damage, excessive wear or heavy deposits), keep them as a spare together with the contact point distributor | ||
| - | ==== ⚙️ | + | ==== Timing Adjustment ==== |
| - Clear all tools and debris from the engine bay | - Clear all tools and debris from the engine bay | ||
| Line 126: | Line 124: | ||
| {{: | {{: | ||
| - | ==== 🧹 Clean Up ==== | + | ==== Clean Up ==== |
| - Finish any remaining heatshrinking or taping | - Finish any remaining heatshrinking or taping | ||
| - Dress the cable run to minimise stress and short-circuit risk; cable-tie to existing harness or pipes | - Dress the cable run to minimise stress and short-circuit risk; cable-tie to existing harness or pipes | ||
| - Final check: no tools or debris left in the engine bay | - Final check: no tools or debris left in the engine bay | ||
| - | |||
| - | |||
projects/automotive/kancil/k4_660_upgrades.txt · Last modified: by Andrew Yong
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
